The Magnetic Pulser ^™

High Intensity Momentary Time-Variant Pulsed DC Magnetic Field Therapy Generator

Magnetic Pulser or Magnetic Pulse Generator for Magnetic Field Therapy based on research of Dr. Bob Beck

[MODEL #: MPG3] - NEW Model!

"First Aid Kit of the Future"

as per the research of Dr. Robert (Bob) C. Beck, D.Sc.

"The best Magnetic Pulser on planet Earth!" says Dr. Beck

---

Our design of The Magnetic Pulser is CERTIFIED, APPROVED and Personally ENDORSED by
Dr. Robert (Bob) C. Beck, D.Sc.

Description International Voltage  Requirements  Disclaimer Warranty Cost Ordering Research Info
Other Products Everything You Need to Know Before You Buy Y2K

What is "The Magnetic Pulser"?

Full instructions about the use and benefits of The Magnetic Pulser ^™ can be found in the research papers published by Dr. Robert (Bob) C. Beck. For an on-line read of the original Patent # 5,188,738 click here.

The Magnetic Pulser is a professionally designed quality device, thoroughly tested and guaranteed to operate as per the specifications in Dr. Bob Beck's research. The Magnetic Pulser (MPG) is designed to generate an intense (~33,068 Gauss), momentary (~2.5mS) pulsed DC magnetic field (click here to see the actual waveform).

NOTE: Please do not confuse this device with permanent/ceramic magnet therapies, or with the EMR (electro-magnetic radiation) producing devices!

Through the principle of induction, this magnetic field creates eddy-currents (tiny electrical micro-currents) in living organic material that contain an electrolyte such as saline. The result is the same as what The Silver Pulser does, only the Magnetic Pulser requires no contact, and can be used to target specific areas.

This device for research purposes only. Before using, consult your professional health practitioner or Medical Doctor.

---

Unique Features:

• Fully Endorsed and Approved by Dr. Robert C. Beck, D.Sc. (Ours is the only MPG to receive endorsement and approval. In fact, Dr. Beck uses our MPG personally.)

• New Hand-Paddle design. Our pulsing coil has been fully re-designed into a custom molded plastic enclosure complete with clear identification of the Bio-North (-) Magnetic Pole.

• A unique circuit design allows The Magnetic Pulser to operate without the use of a Xenon flashtube (as did previous designs) allowing for maximum power delivery to the coil.

• Fully Automatic! The MPG3 will automatically charge and discharge - no manual pulsing required. An internal Digital Counter allows the MPG3 to pulse 64 times automatically. Simply reset the unit to continue.

• LED light bargraph. A light bargraph consisting of five Green LED lights, illuminates sequentially giving visual indication of the MPG3 charging up. A dual function Red LED light indicates either a count of 64 has been reached, or an overload condition has occurred.

• Operates from an AC-DC Wall Adapter (included), or from a 12 Volt DC source like a automobile battery, appropriate solar panel, etc.

• Extremely high power output. Generates ~32.67 Joules (Watt*Seconds) of energy through the use of a 600uF, 330VDC Custom Photoflash Capacitor. This then produces ~33,068 Gauss (~33 kiloGauss) magnetic field in the coil.

• High-Frequency Custom Switch Mode Pulse-Width-Modulated (PWM) power supply allows for fast charges (3.5 seconds) and a very lightweight unit. Our PWM power supply is a constant-current design.

• Double-insulated practices used throughout to ensure the greatest electrical safety. Coil is completely enclosed in a custom-molded plastic Hand Paddle. No exposed wires or leads.

• Extremely long capacitor lifetime. We now have a custom strobe type capacitor designed specifically for our Magnetic Pulser. Expect well over a 1/4 million (250,000) cycles of operation before our custom capacitor requires replacement (at a nominal charge). Compare this with our previous version the MPG1 which has a 85,000 cycle life, or even to photoflash based pulsers that have 5,000 - 10,000 life cycle.

• Very Fast charging cycle. Unit fully charges in 3.5 seconds.

• Overload Protection. Should an overload or fault condition occur in the charging section, a sensor will limit the current, then eventually shutdown the unit until the fault condition is removed.

• Bio-North Magnetic Pole Polarity (-) or South-Seeking is clearly identified on one side of pulsing coil. This give the user the choice of applying either Bio-North (-) or Bio-South (+) pole energy to the site.

• Our Electrical Circuit Boards are GOLD Plated for extreme reliability and workmanship.

• Compact and lightweight. MPG3 unit weighs 3/4 Lbs. (0.3 Kg.), Magnetic coil weighs 1 Lb. (0.4 Kg.). Total shipping weight of complete MPG3 with wall adapter weighs ~3 Lbs. (~1.3 Kg.).

The Unit:

Operating Manual for this device in Adobe Acrobat PDF format, please go to our Downloads page by clicking on this link: A HREF="http://www.sotainstruments.com/downloads.htm"http://www.sotainstruments.com/downloads.htm/A)>
The Magnetic Pulser is housed in an attractive ABS "pc-bone" coloured (Pantone "Warm Grey 1") plastic box. A Toggle Switch turns the Magnetic Pulser on and off. A series of Green lights indicates power is available and visually shows unit is charging. When turned on, the Magnetic Pulser will immediately begin to charge up (in about 3.5 seconds). When fully charged, the last Green light will go on briefly, and the unit will immediately discharge the stored energy of the capacitor into the pulsing coil. The Magnetic Pulser will then begin another charge cycle.

Should an overload or fault condition occur in the charging section, the MPG3 will shutdown until the fault condition is removed, and a Red indicator light will come on. After 64 pulses, the MPG3 will go into stand-by mode until a physical reset occurs. This helps prevent continuous operation should the MPG3 be left on unattended. A Red light will illuminate.

The Magnetic Pulser is packaged in a lidded cardboard "die-cut mailer" box for easy storage.

Electronics:

The Magnetic Pulser is designed as per the research by Dr. Bob Beck. We have improved on the design with added features. These changes by no means alter the effectiveness of the unit. Our electronic design is unique and efficient making the unit very reliable and powerful. Early designs required the use of a Xenon flashtube. We've completely re-designed The Magnetic Pulser from the ground up using the latest in electronic components. The result is a very powerful, reliable, rugged device that transfers more energy to the output coil. In addition, we use double-insulation techniques to ensure the greatest in electrical safety. This is of extreme importance!

Specifications (as measured on a Tektronics TDS 210 Digital Real-Time Oscilloscope, and Wavetek AD105 Clamp-On RMS Ammeter)

• Energy Storage Capacitor: 600uF, 350 Volts DC
• Typical Energy Storage: 32.67 Joules (Watt*Seconds)
• Maximum Energy Storage: 36.75 Joules (Watt*Seconds)
• Typical Peak Charge Voltage: 330 Volts DC
• Maximum Peak Charge Voltage: 350 Volts DC
• Minimum Peak Current Discharge into Coil: 115 Amps RMS
• Typical Charge Time: 3.5 Seconds
• Pulse Rise Time: <1.8 uS (microseconds) Click here to see the actual waveform
• Pulse Duration: ~2.5mS (milliseconds) Click here to see the actual waveform
• Main Coil Inductance: ~2.5mH (millihenries)
• Flux Density: 31,050 Ampere*Turns
• Peak Magnetic Field Output: 33,068 Gauss (~33 kiloGauss).

Dimensions:

The Magnetic Pulser is 5.00" wide x 5.25" long x 2.00" high (12.5 cm wide x 13.25 cm long x 5.0 cm high). Casing is high-impact ABS plastic. Weight of The Magnetic Pulser unit is about 3.0 Lbs. (1.3 Kg.) total. Case is "pc-bone" in colour (Pantone "Warm Grey 1").

Each Magnetic Pulser comes complete with:

• The Magnetic Pulser unit

• Operating Manual
• Additional Documentation for Researchers (which is mailed to you separately)
• AC-DC Wall Adaptor rated at 12 Volts DC @ 1.2 Amps, centre positive. (NOTE: This wall adapter can be used on The Silver Pulser,
• Cardboard "die-cut mailer" Storage Box
• 1 Year Parts and Labour Warranty

International Voltage (220 or 240 Volt Mains) Requirements:

CAUTION: DO NOT plug the Magnetic Pulser's power supply into your 220VAC or 240VAC Mains!! Severe damage or injury may result, voiding the warranty!!

If you are intending to use the Magnetic Pulser outside of North America where the voltage is not 110VAC, 60 Hz (cycles) here are your options:

1. Purchase the International / Universal Wall Adapter. Please see our Products page for details.

2. Use a voltage matching adapter (transformer) which allows a North American 110VAC, 60Hz device to operate from your 220 VAC or 240 VAC, 50Hz Mains. These are readily available from electronics stores. Select a 25 Watt or greater adapter. The Magnetic Pulser's power supply will then plug directly into the adapter.

3. Purchase the Magnetic Pulser without its power supply. Instead, purchase a power supply from local electronics store with these specifications: 220 VAC or 240 VAC, 50Hz input, 12 Volt DC output @ 1.2 Amps or greater, Centre Positive, 2.1mm Plug

4. Additionally, the Magnetic Pulser may also be operated directly from a 12 Volt DC Battery like via an automobile cigarette lighter. You will need to purchase an adapter cord which plugs into the cigarette lighter and has a Centre Positive, 2.1mm Plug.

Disclaimer:

What about a Warranty?

How much is "The Magnetic Pulser"?

Our Policy at Teslatech: "We encourage you to educate yourself before purchasing any of our units. When ill, it's easy to make a decision in desperation rather than based on information." "We are a company that believes in self-responsibility for ourselves and our customers. Once you purchase and use our units we cannot take responsibility for your decision." "If, however, the unit has not been used at all, we will refund the full purchase price within 30 days of purchase." "Thank-you for your understanding." Please note: Personal cheques will be held for 30 days to allow funds to clear.

How can I Order "The Magnetic Pulser"?

Please note: If you are ordering by FAX, E-Mail, or Mailing us a Money Order please remember to include the following important and necessary information so we can process your order without delays (especially International Orders!): Your Full name and street address. (Remember, couriers will NOT deliver to PO Boxes.) Telephone Number and, if available FAX Number. (Couriers MUST have a Telephone number, or they cannot deliver. And we need a way of contacting you should there be a shipping problem.) Your E-Mail address if applicable (especially International Orders), so we can contact you easily should there be a shipping problem.

Please note: Personal cheques will be held for 30 days to allow funds to clear.

Call 1-541-434-0318 Or: Tel: 1 + (250) 814-0046 Fax: 1 + (250) 814-0047 For United States inquiries/orders write to: Teslatech, 1430 Willamette St #202 Eugene, OR 97401 Or e-mail to mail@teslatech.com NOTE: This is NOT a secure page. Please DO NOT e-mail your credit card numbers or other sensitive data. Thank-you!

Where can I get more information on Dr. Robert (Bob) C. Beck's research? From Us! Please mail@teslatech.com for more info!